Sulzer Pump Designations-manufacture,factory,supplier from China

ANSI Mark III 4x3-10H bare shaft pump in WCB material, other materials like CD4M, CF8M, A20 etc are all available. And our pumps are 100% interchangeble with leading enterprise's one.If any needs, pls contact me for quotation.

It seems there might be a slight mix-up with the pump terminology. As of my last update in January 2022, there isn't a widely recognized "WPP Pump" specifically within the domain of industrial or commercial pump systems. However, pumps with the prefix "WPP" could be a colloquial term, an abbreviation, or perhaps referring to a specific model or brand known in certain industries.To provide more accurate information, could you confirm if you're referring to a specific type of pump or a brand?

PerformanceHead up to 110 m. Temperature max. 180 °C. Capacity up to 2000 l/s. Operating frequencies 50 or 60 Hz. Pressure up to 1.6 MPa, depending on material and size.

The hydraulic design of two-phase flow pulp pump adopts the principle of “Relative suction and relative blocking”in the theory of two-phase flow, so that the hydraulic performance of the flow parts of the pump conforms to the law of solid-liquid two-phase flow, thus reducing the slurry flow parts of the erosion and wear, greatly improving the efficiency and service life of the pump, the pump series has the following notable features:1.High efficiency and energy saving: The running efficiency is 3-10 percentage points higher than the average of the ordinary pulp pump, the energy saving and cons

We are at Pump&Fluid Euipment Exhibition

Our pump can meet many kinds of different application, take the following example:Soda Pump                                                                          ANSI B.73.1Size In/ Out : 10 Inch/ 8 Inch Flange ANSI 150 FFDuty Point:Liquid : Caustic Soda/ Sulphamite AcidCapacity : 8 M3/Min ( 480 M3/H )Head : 40 Meter ( 131 Ft )Temperature : 80 deg CPH : 4 – 10SG : 1.47If any needs, pls let me know.

CASING• Bonus casing thickness: Class 150 pumps feature Class 300 wall thickness as standard; increased reliability and maximized casing life.• Top centerline discharge for air handling, self venting.• Back pull-out design for ease of maintenance.• Integral casing feet prevent pipe load misalignment − maximized seal and bearing life.• Serrated flanges standard for positive sealing against leakage. Meets ANSI B16.5 requirements. Class 150 FFflanges standard, optional Class 150RF, 300 FF/RF.If any needs, pls contact me for quotation.

Besides casting pump parts and maching pump parts, we also supply gasket, bearing, O-ring, oil seal etc accessories for assembling a pump.Pls let me know if any needs, I'd like to offer you for your reference.

The cam pump [2-3] adopts the cartridge combined floating mechanical seal to replace the existing spring thrust mechanical seal structure.Cam pump [3] pump rotor: it adopts nano composite wear-resistant rubber rotor, which is resistant to dry running. The idling time is more than 60 minutes, and the pump body is solid and durable, with long service life;The wide head seal is used to optimize the rotor profile design, so as to ensure that the rotor and the pump seal are face seals.

First. Classification by impeller number 1. Single-stage pump: that is, there is only one impeller on the pump shaft. 2. Multi-stage pump: that is, there are two or more impellers on the pump shaft, and the total lift of the pump is the sum of the lifts generated by n impellers. Second, classified according to work pressure 1. Low-pressure pump: the pressure is less than 100m H2O; 2. Medium pressure pump: the pressure is between 100 and 650 meters of water column; 3.

1. Does the vibration generated when the vacuum pump works have any influence on the process and environment? If the process is not allowed, choose a pump without vibration or take anti-vibration measures.2. Understand the composition of the pumped gas, whether the gas contains condensable vapor, whether there is particulate dust, whether there is corrosiveness, etc. When choosing a vacuum pump, you need to know the gas composition, and select the corresponding pump for the pumped gas.

Operating Parameters• Flows to 4540 m3/h (20 000 US gpm) • Heads to 215 m (700 ft) • Pressures to 27 bar (400 psi) • Temperatures from -73°C (-100°F) to 370°C (700°F) • Discharge sizes from 25 mm (1 in) to 200 (8 in)  The material of wet ends like A20, CD4M, 316SS, Titanium, Hastelloy C, Nickel etc are all available, if any needs, I'd like to offer you for your reference.